W90N740 Boot Loader [ Version 1.1 $Revision: 6 $ ] Rebuilt on Sep 26 2003 Running on a W90N740 Evaluation Board Board Revision 1.0, W90N740 MCU Memory Size is 0x800000 Bytes, Flash Size is 0x200000 Bytes Board designed by Winbond Hardware support provided at Winbond Copyright (c) Winbond Limited 2001 - 2003. All rights reserved. Boot Loader Configuration: TFTP server port : MAC 1 Network phy chip : DAVICOM DM9161E MAC 0 Address : 00:69:70:63:6D:21 IP 0 Address : 0.0.0.0 MAC 1 Address : 00:91:00:00:30:48 IP 1 Address : 0.0.0.0 DHCP Client : Enabled CACHE : Enabled BL buffer base : 0x00300000 BL buffer size : 0x00100000 Default baud rate : -1 For help on the available commands type 'h' Press ESC to enter debug mode ...... Cache enabled! Processing image 1 ... Processing image 2 ... Processing image 3 ... Processing image 4 ... Processing image 5 ... Processing image 6 ... Processing image 7 ... Unzip image 7 ... Executing image Linux version 2.4.20-uc0 (clyu2@localhost.localdomain) (gcc version 3.0) #955 Fri Oct 17 16:15:14 CST 2003 Processor: Winbond W90N740 revision 1 Architecture: W90N740 On node 0 totalpages: 2048 zone(0): 0 pages. zone(1): 2048 pages. zone(2): 0 pages. Kernel command line: root=/dev/rom0 Calibrating delay loop... 39.83 BogoMIPS Memory: 7MB = 7MB total Memory: 5880KB available (920K code, 192K data, 40K init) Dentry cache hash table entries: 1024 (order: 1, 8192 bytes) Inode cache hash table entries: 512 (order: 0, Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 2048 (order: 1, 8192 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Winbond W90N740 Serial driver version 0.9 (2001-12-27) with no serial options enabled ttyS00 at 0xfff80000 (irq = 6) is a W90N740 Blkmem copyright 1998,1999 D. Jeff Dionne Blkmem copyright 1998 Kenneth Albanowski Blkmem 1 disk images: 0: 7F0C0000-7F1B47FF [VIRTUAL 7F0C0000-7F1B47FF] (RO) RAMDISK driver initialized: 16 RAM disks of 1024K size 1024 blocksize loop: loaded (max 8 devices) The flash size:0x00200000 Boot Loader Configuration: TFTP server port : MAC 1 Network phy chip : PHY MAC 0 Address : 00:69:70:63:6d:21 IP 0 Address : 0.0.0.0 MAC 1 Address : 00:91:00:00:30:48 IP 1 Address : 0.0.0.0 DHCP Client : Enabled CACHE : Enabled 01 eth0 initial ok! which:0 01 eth1 initial ok! which:1 PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered Linux video capture interface: v1.00 Welcome wireless network! :) GPIO: 50d0 wireless driver reset failed, dfbe prism: error -5 registering device "wlan0" AM29LV160DB Flash Detected usb.c: registered new driver hub add a static ohci host controller device : USB OHCI at membase 0xfff05000, IRQ 9 hc_alloc_ohci usb-ohci.c: AMD756 erratum 4 workaround hc_reset usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver audio audio.c: v1.0.0:USB Audio Class driver usb.c: registered new driver W99683 W99683.c: v1.00 for Linux 2.4 : W99683 USB Camera Driver NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (establ VFS: Mounted root (romfs filesystem) readonly. Freeing init memory: 40K Shell invoked to run file: -t Command: mount -t proc none /proc Command: mount -t ramfs none /usr Command: mount -t ramfs none /swap Command: mount -t ramfs none /var/run Command: mount -t ramfs none /etc/Html/Reboot Command: cp /etc/Html/Ctl/Reboot.htm /etc/Html/Reboot/Reboot.htm Command: ifconfig lo 127.0.0.1 Command: #ifconfig eth1 hw ether 00:1c:2a:42:46:11 Command: ifconfig eth1 up MiiStationWrite 1 MiiStationWrite 1 Wait for auto-negotia 100MB - Full Duplex Command: camera.flat& [15] Command: mctest& new USB device :801cd804-15d6c0 hub.c: new USB device 1, assigned address 2 [16] Command: sh 2003/2/1 0:0:0 Total size 6180 Web Camera Version: Apr 3 2005 13:00:04 . pcConfigParam->CheckSum:62828799 probing for device..., 0 probe: vendorID: 416, ProductID: 6830 Find W99683 USB Camera video name: W99683usb W99683.c: Device registered on minor 0 Initializing eth1... p1[7]:1,j 2,config->bNumInterfaces:3 usbaudio: device 2 audiocontrol interface 1 has 1 inp ing interfaces usbaudio: valid input sample rate 8000 usbaudio: device 2 interface 2 altsetting 1: format 0x00000010 sratelo 8000 srat ehi 8000 attributes 0x00 usbaudio: registered dsp 14,3 usbaudio: no mixer controls found for Terminal 2 usb_audio_parsecontrol: usb_audio_state at 0014ec60 MCTEST:SendRequest:NetConnect error MCTEST:SendRequest:NetConnect error MCTEST:mc_tx_socket:sendto failed -1,errno:19 MCTEST:SendRequest:NetConnect error MCTEST:SendRequest:NetConnect error MCTEST:mc_tx_socket:sendto failed -1,errno:19 Sash command shell (version 1.1.1) /> Before execv /bin/dhcpc. Reboot !!! Port[0]:80 Port[1]:0 Port[2]:0 Start http server at: [/etc/Html] __pthread_initial_thread_bos:5f0000 manage pid:19 open dev/video0 success! Open dev/dsp success! Prepare Audio Buffer 0x7e 256 16 16 256 129 ( 128 128 128 128 0 ) ver: 507 0 3 Error: Camera/CameraCtl.c, 178. Error: Camera/CameraCtl.c, 178. pCameraParam->ulImgChannel:0 The camera is W99683usb Driver.c: mode 0 channel:0,:256 ret:0 />